The tides are the breath of the ocean; understanding them is about more than just knowing when high water is; it’s about efficiency, safety, and making sure you always have water under your keel. For sailors used to the steady levels of Lake Zurich, Lake Zug or Lake Geneva, the massive tidal ranges of the Atlantic can be a shock. Understanding tides is one of the single biggest steps in converting your lake skills into offshore competence.

For those who want a refresher—or if you missed our recent talk on tides—here is a summary of the key concepts we covered.

Why Tides Matter

Tides affect us in two ways: vertically (height) and horizontally (stream/current).

• The Positive: They provide “free horsepower” when the stream is with you and allow access to shallow harbours at high water.
• The Negative: They can leave you high and dry if you miscalculate, slow you down if you fight the current, or create dangerous sea states like “wind-over-tide”.

What Causes Tides? (The Earth, Moon & Sun)

Tides are essentially a tug of war between the Earth, Moon, and Sun.

• The Primary Driver: The Moon has the biggest influence because it is closer to Earth. Gravity pulls the water into a “bulge” on the side facing the Moon, and then pulls the Earth into this bulge, leaving a corresponding high-tide bulge on the far side of the planet.
• The Sun’s Role: While less powerful than the Moon regarding tides, the Sun reinforces or counteracts the Moon’s pull depending on their alignment.

What is the difference between Spring and Neap Tides?

Understanding the phase of the moon is your first step in predicting the tidal range.

• Spring Tides (Big Range): Occur at New Moon & Full Moon. The Sun, Moon, and Earth line up, combining their gravity to create higher highs and lower lows.
• Neap Tides (Small Range): Occur at the Quarter Moons. The Sun and Moon are at 90° to each other, partially cancelling out their forces. This results in lower high tides and higher low tides.

Tide Tables

Tide Tables are published by most ports (or can be looked up online) and contain the information of High and Low Water and the tidal heights of both High and Low Water. Be careful with the times as they are usually in the local times and do not adjust for “summer time”. In the summertime, you may have to add an hour to get the correct time.

Navigation Essentials: Height & Depth

When planning a passage, remember that charts use Chart Datum (CD), which is usually the Lowest Astronomical Tide (LAT)—the lowest the tide is predicted to fall under average conditions.

• The Formula: Actual Depth = Charted Depth + Height of Tide.
• Drying Heights: Watch out for underlined numbers on the chart; these are rocks or banks that dry out at LAT.

Glossary of Essential Tidal Terms

• LAT: Lowest Astronomical Tide (lowest possible tide under normal meteorological conditions)
• Chart Datum: Depth of Water (or Drying Heights) at LAT.
• MHWS/MLWS: Mean High/Low Water Springs
• MHWN/MLWN: Mean High/Low Water Neaps
• Spring Range (average): Is the range between MHWS and MLWS
• Neap Range (average): Is the range between MHWN and MLWN
• Depth of Water: Tidal height + Depth Below Chart Datum or Tidal Height – Drying Height
• HAT: Highest Astronomical Tide (Highest tide possible under normal meteorological conditions. Clearing height under bridges are from HAT)
• Height of Light: Height of the light signal above MHWS

The Rule of Twelfths (How to calculate tidal heights?)

For semi-diurnal tides (like we have in Europe/Atlantic), the tide doesn’t rise at a constant speed. It follows a bell curve. To estimate the height at a specific hour, use the Rule of Twelfths:

1st Hour: Rises 1/12th of the range
2nd Hour: Rises 2/12ths of the range
3rd & 4th Hours: Rises 3/12ths (max flow)
5th Hour: Slows to 2/12ths
6th Hour: Finishes with 1/12th

Note: The Rule of Twelfths is an estimation for semi-diurnal tides and should not replace official tide tables for critical clearance

Rule of 12ths Calculator

Estimate tidal height between High and Low water.

Low Water (m)

High Water (m)

Total Tidal Range: 3.0m

Tide flows fastest during Hour 3 & 4

Tide vs. Current: Understanding Tidal Streams

Never ignore the current. Tidal streams can significantly alter your ETA and safety.

• Tidal Diamonds: Look for the magenta diamonds on your chart. These refer to a table giving you the “Set” (direction) and “Rate” (speed) of the current for each hour relative to High Water.
• Tidal Atlases: Visual guides with arrows. Thicker arrows mean stronger currents. Remember that numbers like “12, 23” on these charts often mean 1.2 knots at Neaps and 2.3 knots at Springs.

Meteorological Effects

Meteorology: Tide tables are based only on the movements of celestial bodies (astronomy). They cannot predict the weather. Real-time conditions can change the water level significantly:

• Air Pressure: High pressure pushes down on the sea surface, lowering the water level. Low pressure (depressions) allows the water to rise. A difference of 30 hectopascals can change the sea level by ~30cm (one foot).
• Wind: (Storm Surges): Strong, sustained winds blowing onshore can “pile up” water, creating higher-than-predicted tides. Conversely, offshore winds can push water away, resulting in unexpectedly low tides—a danger for shallow moorings.

Dangers to Watch For

1. Wind over Tide: When the wind blows against the tidal stream, it creates steep, choppy, and dangerous waves.
2. Tidal Races & Overfalls: Fast water squeezed around headlands or flowing over uneven seabeds can cause turbulence. Avoid these when the tide is running hard.

Summary

Safe navigation relies on understanding these cycles. Know your Moon phase (Springs vs. Neaps), check your stream (diamonds and atlases), and always ensure you have enough water under the keel (Rule of Twelfths).

Want to put this into practice or learn more? Join us on one of our activities this coming summer.

The post Sailing Tides Explained: A Guide to Springs, Neaps & Not Getting Stranded appeared first on All Winds Adventures.